V-MD241, 1920x1080 High Resolution Rack mountable Desktop / VESA Mount Monitor with Modular Inputs and Network Control


24", 1920x1080 Resolution Rack mountable Desktop / VESA Mount Monitor Monitor with Modular Inputs and Network Control

Owner's Manual Spec Sheet

> Optional Input Modules


• Swap and interchangeable video modules

• Native 1920 x 1080 resolution screen

• Two available input slots

V-MD241 specifications
Panel Number of Panels 1
Panel Size 24” Diagonal
Resolution 1920 x 1080
Aspect Ratio 16:09
Active Area 531.36 x 298.89 mm
Type LCD Panel
Brightness 300 cd/m²
Contrast 3000:1
Color Gamut YUV, RGB
Viewing Angles (CR>=10) 178° x 178°
Backlight type LED
Adjustable Backlight Yes
Features Video Formats 1080p/1080i/720p/625i/525i
Loss of Input Curtain Yes
Color Temperature D65, D55 and D93
H/V Delay Yes
Under scan Yes
IMD Functions Yes
Tally Yes
False Color Yes
Peaking Filter No
HDMI CSC Auto With HDMI Module
HDMI Ratio Auto With HDMI Module
Pixel to Pixel Yes
Test Signals No
Pre-set Gamma points No
Self-Sensing Yes
Modular Input Slot 2
Re-clocked/Re-Shaped Yes
Video Input Connectors CVBS Yes
YPbPr Yes
SD-SDI Optional Module
HD-SDI Optional Module
3G-SDI Optional Module
HDMI Optional Module
DVI-I Optional Module
Optical Optional Module
Video Output Connectors CVBS Yes
YpbPr Yes
SD-SDI Optional Module
HD-SDI Optional Module
3G-SDI Optional Module
Control Inputs Embedded Audio from SDI Yes
Input Status Display Yes
Tally / GPI Tally
RS-485/422 w/ Loop-Through No
Ethernet Yes
Mechanical Controls on front Panel Yes
User-Defined Function Buttons Yes
RotoMenu™ Control No
Pivot Angle Yes
Handles/Rack Ears Yes
Power Voltage 12 VDC
Consumption 3.5A @ 12VDC (42 W)
Power Switch Yes
Connector 4-Pin Female XLR
Compliance Compliance CE approved

Operating Temperature (C°) 32°F to 104°F
Storage Temperature (C°) -4°F to120°F
Rack Unit dimensions 22"(W) x 14.66" (H) x 1.5 (D)
Weight (Main Body) 11.05 lbs
Protective screen No
Vesa Mount Pattern 200/75mm

Network Control

V-MD series rack LAN port built-in web serverEach V-MD series rack includes a LAN port with a built-in web server. This allows the operator to visually monitor and control any or all V-MD series units that are connected to the LAN. Any function that is addressable from the front panel of a V-MD series monitor can be accessed via any Firefox® web browser -- even on a wireless device.** The rear panel LAN 100 port connects the unit to the LAN.

Once connected, the user simply locates the IP address of any one of the units connected to the LAN. This is accomplished by going to the MAIN MENU of any of the connected units and selecting the NETWORK CONFIGURATION submenu. This will then display the IP address of that unit. V-MD units are shipped with the DHCP mode enabled.

MD Network Control IP Address on screen sampleSimply type this IP address into the address bar of your browser and the home page for that unit will appear. It is possible to poll your LAN for all other MD units connected by accessing the NETWORK tab from the Top Menu.

MD Network Control Power and InputThe user can then control multiple networked MD monitors at once using a single browser page. The user may select which monitor(s) they wish to control and send commands to those particular monitors. The browser provides real-time status of any connected monitor, ensuring consistent signals / feeds and so forth.

False Color Filter

Color filter scale

The False Color filter is used to aid in the setting of camera exposure. As the camera Iris is adjusted, elements of the image will change color based on the luminance or brightness values. This enables proper exposure to be achieved without the use of costly, complicated external test equipment.

To best utilize this feature, you must understand the color chart and have a basic understanding of camera exposure. Normally, when shooting subjects like people, it is common practice to set exposure of faces to the equivalent of approximately 56 IRE. The False Color filter will show this area as the color PINK on the monitor. Therefore, as you increase exposure (open the IRIS), your subject will change color as indicated on the chart: PINK, then GREY, then a few shades of YELLOW. Overexposed subjects (above 101 IRE) on the monitor will be shown as RED. In addition, underexposed subjects will show as DEEP-BLUE to DARK-BLUE, with clipped-blacks indicated with a FUCHSIA-like color. Lastly, the color GREEN is used to indicate elements of the image that are approximately 45 IRE. This represents a "neutral" or "mid-level" exposure commonly used for objects (not people).

Filter display samples
Overexposed objects will display as RED
Underexposed objects show as
Properly exposed objects will display elements of GREEN and PINK

IMD and Tally

Use the "Text Enable" function to turn the MD Text feature ON. This will cause the "Text String" to appear on the lower portion of the screen. This provides the user with a 16 character on-screen text string. The color, background (opacity), and alignment of text can also be managed by the operator. This same menu allows control of Tally Source. Tally lights (both LED and on-screen) can be enabled/disabled and also set to match "Text String" color.

Optional Input Modules (Type A modules)

MD-3GE - 3G/HD/SDI Input Module with Loop-Through
MD-HDSDIx2-A - Two-channel HD-SDI Input Module with switched output
MD-HDIx2-A - Two-channel HDMI Input Module
MD-DVII-A - DVI-I Input Module

» Click here for more info on Optional Input Modules
* Input modules are optional and available at additional cost. More input modules to be offered in the future.

* Pricing does not reflect freight costs and applicable taxes and duties
* Pricing, specification and features are subject to change

Modular Design